Backup rings

Backup (support) rings are used for both static and dynamic applications, preventing the migration or extrusion of the O or X-ring in the gap as pressurisation and de-pressurisation/pressure cycling occur. The profile shape of the backup rings is usually rectangular but may also be concave at the face mating with the O-ring. Manufactured in various PTFE compounds, backup rings may be continuous, slotted or spiralled.

The continuous STE design is predominantly used for internal, radial-static and dynamic applications.
The slotted STG design is for external sealing, radial-static and reciprocating applications.

The spiralled STS design can be used for both external sealing and internal sealing applications. Compared with the other two designs, this form offers the advantage that, in service conditions involving high temperature fluctuations, the ring is able to compensate for larger tolerance changes without problem through spiral contraction or extension.

Type ST… backup rings are manufactured as standard from unfilled PTFE. This material is ideally suited to light to medium-duty applications. In the case of heavier-duty requirements, the PTFE material must be filled. As a rule, the filler material takes the form of fibreglass, although the PTFE may also be reinforced by bronze or carbon.

The STE continuous and STG slotted designs can also be manufactured in other materials such as PU, POM, PA etc. where necessary.

The STM types for metric size ranges and STI designs for inch sizes are manufactured from a special polyester elastomer in the injection moulding process. Owing to its high resilience, this material offers the advantage that it can also be used for external sealing in continuous grooves. These backup rings are likewise available in polyurethane. Simple snap-fitting and automatic installation are likewise possible with the above-mentioned materials. Selection of the appropriate material combinations also ensures that these backup rings exhibit a high level of extrusion resistance.

Benefits

Wide range of different materials
Very good thermal and chemical resistance
Individual size ranges possible
Simple groove design
Capability to bridge large seal gaps
Easy to fit

Application ranges

Velocity:	reciprocating / rotating up to approx. 2 m/s (depending on material)
Temperature:	- 60° C to + 200° C (depending on material selection)
Pressure:	up to 200 MPa (2000 bar) static load (depending on material selection) up to 40 MPa (400 bar) dynamic load (depending on material selection) up to 15 MPa (150 bar) rotating load (depending on material selection)

Installation

It is recommended to provide backup rings where relatively high pressures in excess of approx. 5 MPa (50 bar) are involved, and particularly where relatively large gap dimensions need to be bridged between the components requiring sealing. A backup ring is also advisable in applications involving high velocities and frequencies, heavy pulsation, elevated temperatures and, in particular, temperature fluctuations.

In single-acting applications where pressurisation only takes place on one side, it is usually sufficient to install one backup ring on the non-pressurised side. If reciprocating pressurisation is expected, two backup rings will need to be used, one on either side of the O or X-ring.

The use of backup rings enables the specified gap dimensions to be somewhat enlarged, although the clearance fit H8/f7 is recommended in order to ensure functional reliability.

The recommendations relating to the groove dimensions and surface finish, i.e. roughness, tolerances, insertion bevels etc. are essentially the same as those applicable to O-rings.

Directives

All information and values stated concerning our product portfolio are based on the knowledge optained through a long experience of manufacturing and application.
These figures are for indicative purposes only and may vary (exceed or deceed) according to the particular circumstances. Unknown factors in the applications and practice can considerably change the conditions and reduce and change statements, which may cause the above information to be invalid.
No liability can be accepted for any mistakes or omissions, error and subject to change without prior notice.

News

We've moved

From 24 August, 2020 we will be available in our new premises at the new address.

[more]

The new S.F. Product Catalogue has been released!

Hot of the Press - ask for your personal edition: Info@sf-components.com | +49 / 8141 / 353 54 - 0 Or as download directly here. Individual product categories you find under ser

[more]